PAULCO TE-2501 CLEAR EPOXY PART-A 1-GAL. - Epoxy Paint - Toll Manufacturing



M A T E R I A L S A F E T Y D A T A S H E E T

PAULCO TE-2501 CLEAR EPOXY PART-A 1-GAL.		Page: 1


PRODUCT NAME: PAULCO TE-2501 CLEAR EPOXY PART-A 1-GAL. HMIS CODES: H F R P
PRODUCT CODE: PCO2501CLR-A-1 2 1 0 I

================== SECTION I – MANUFACTURER IDENTIFICATION =================

MANUFACTURER’S NAME: Viking Paints Inc.
ADDRESS : 100 WEST 78TH ST.
RICHFIELD,MN 55423

EMERGENCY PHONE : 1-800-535-5053 24HRSDATE PRINTED : 2/4/2009
INFORMATION PHONE : 1-612-866-1212 NAME OF PREPARER : T. KINSELLA

========== SECTION II – HAZARDOUS INGREDIENTS/SARA III INFORMATION =========

VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
————————————————————————————————————————
* XYLENE (MIXED ORTHO,META AND PARA ISOMERS) 1330-20-7 6 68F .7% TO .8%
OSHA PEL/TWA: 100 PPM OSHA PEL/STEL: 150 PPM
ACGIH TLV/TWA: 1OO PPM ACGIH TLV/STEL: 150 PPM
LD50 ORAL: 4.3 G/KG (RAT) LD50 DERMAL: 3.95 ML/KG (RABBIT)
LC50 INHALATION: 5000 PPM/4H (RAT)
SARA HEALTH ASSESSMENT RANK 72
* ETHYLBENZENE 100-41-4 7.1 68F .1% TO .2%
OSHA PEL/TWA: 100PPM OSHA PEL/STEL: 125PPM
ACGIH TLV/TWA: 100PPM ACGIH TLV/STEL: 125PPM
LD50 ORAL: 3500 MG/KG (RAT) LD50 DERMAL: 17800 MG/KG (RABBIT)
LC50 INHALATION: LCLO: 400PPM/4H (RAT)
SARA HEALTH ASSESSMENT RANK 69


* Indicates chemical(s) subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
N/A

=============== SECTION III – PHYSICAL/CHEMICAL CHARACTERISTICS ============

BOILING RANGE: 0 deg F – 276 deg F SPECIFIC GRAVITY (H2O=1): 1.116
VAPOR DENSITY: LIGHTER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
COATING V.O.C.: 0.092 lb/gl MATERIAL V.O.C.: 0.092 lb/gl
SOLUBILITY IN WATER: NON-SOLUBLE
APPEARANCE AND ODOR: COLORED OR CLEAR LIQUID, FAINT ODOR

================= SECTION IV – FIRE AND EXPLOSION HAZARD DATA ==============

FLASH POINT: 68 deg F METHOD USED: TCC
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 0 UPPER: 7

EXTINGUISHING MEDIA: USE “ALCOHOL” FOAM, CO2, DRY CHEMICAL, WATER FOG

SPECIAL FIREFIGHTING PROCEDURES
FULL PROTECTIVE EQUIPMENT, INCLUDING SELF-CONTAINED BREATHING APPARATUS, IS RECOMMENDED. WATER FROM FOG NOZZLES MAY BE
USED TO COOL CLOSED CONTAINERS TO PREVENT PRESSURER BUILD UP.


UNUSUAL FIRE AND EXPLOSION HAZARDS
WHEN HEATED ABOVE THE FLASH POINT, EMITS FLAMMABLE VAPORS WHICH, WHEN MIXED WITHAIR, CAN BURN OR BE EXPLOSIVE. FINE
MISTS OR SPRAYS MAY BE FLAMMABLE AT TEMPERATURES BELOW THE FLASH POINT.



M A T E R I A L S A F E T Y D A T A S H E E T

PAULCO TE-2501 CLEAR EPOXY PART-A 1-GAL.		Page: 2



======================== SECTION V – REACTIVITY DATA =======================

STABILITY: STABLE
CONDITIONS TO AVOID
REFER TO SECTIOINS IV, VI, VII AND VIII.

INCOMPATIBILITY (MATERIALS TO AVOID)
NONE REASONABLY FORESEEN.

HAZARDOUS DECOMPOSITION OR BYPRODUCTS
CO, CO2, SMOKE.

HAZARDOUS POLYMERIZATION: WILL NOT OCCUR

==================== SECTION VI – HEALTH HAZARD DATA =======================

INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Eye watering, headaches, nausea, dizziness and loss of coordination. Excessive inhalation of vapors in high concentra-
tiions may result in narcosis. (Central Nervous System depression.)


SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Skin: Prolonged or repeated exposure can cause moderate irritation, defatting, and dermatitis. Eyes: Severe irritation,
redness, tearing and blurred vision.


SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Repeated exposure of the skin to this product can lead to redness or irritation of the skin. Skin redness or skin rash
may be early signs of potential dermatitis. Avoid repeated skin contact.


INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
GASTROINTESTINAL IRRITATION, NAUSEA, VOMITING AND DIARRHEA. ASPIRATION OF MATERIAL INTO THE LUNGS CAN CAUSE CHEMICAL
PNEUMONITIS WHICH CAN BE FATAL.


HEALTH HAZARDS (ACUTE AND CHRONIC)
Chronic exposure may cause damage to the Central Nervous System, Respiratory System, Lungs, Eyes, Skin, Gastrointestinal
Tract, Liver, Spleen and Kidneys.


CARCINOGENICITY: NTP CARCINOGEN: No IARC MONOGRAPHS: No OSHA REGULATED:
No

Generally not available or not established. IARC monograph pertains to dry barium sulfate powder only.

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Any person with known medical problems with lungs or skin needs a doctor’s opinion as to working with this product.

EMERGENCY AND FIRST AID PROCEDURES
Inhalation: Remove to fresh air. If breathing difficulty persists, consult a physician. Eye Contact: Flush with water
for at least 15 minutees; call a physician. Skin Contact: wash with soap and water. If irritation occurs, consult a
physician. Ingestion: In the unlikely event of ingestion, call a physician immediately and have the names of
ingredients available from Section II.


=========== SECTION VII – PRECAUTIONS FOR SAFE HANDLING AND USE ============



M A T E R I A L S A F E T Y D A T A S H E E T

PAULCO TE-2501 CLEAR EPOXY PART-A 1-GAL.		Page: 3



STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Ventilate area.Remove sources of ignition.Prevent skin contact & breathing of vapor. Wear properly fittetd NIOSH/MSHA
vapor/particulate rrespirator. Confine and remove material with inert absorbent.


WASTE DISPOSAL METHOD
Do not allow material to contaminate ground water systems. Incinerate absorbed material in accordance with federal,
state and local requirements.Do not incinerate in closed containers.


PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Observe label precautions. Keep away from heat, sparks and flame. Close container after each use. Ground containers when
pouring. Wash thoroughly after handling and before eating or smokiing. Do not store above 120 degrees F.


OTHER PRECAUTIONS
Do not sand, flame cut, braze or weld dry coating without a NIOSH/MSHA approved respirator or appropriate ventilation.

===================== SECTION VIII – CONTROL MEASURES ======================

RESPIRATORY PROTECTION
NIOSH/MSHA approved mask for vapors, if working indoors in poorly ventilated areas.

VENTILATION
Local exhaust. Insure adequate ventilation.

PROTECTIVE GLOVES
Butyl gloves are recommended.

EYE PROTECTION
Desirable in all industrial situations. Monogoggles recommended.

OTHER PROTECTIVE CLOTHING OR EQUIPMENT
No special clothing, rubber apron advisable.

WORK/HYGIENIC PRACTICES
AFTER HANDLING PRODUCT, WASH HANDS THOROUGHLY BEFORE EATING, SMOKING, APPLYING COSMETICS, OR USING THE RESTROOM. IT IS
SUGGESTED THAT A SOURCE OF CLEAN WATER BE AVAILABLE IN THE WORK AREA FOR FLUSHING EYES AND SKIN.


========================= SECTION IX – DISCLAIMER ==========================

The information in this MSDS is provided without any representation or warranty expressed or implied, regarding its
accuracy or completeness. The handling, storage, use & disposal of the product are beyond our control. We do not assume
responsibility & disclaim liability for loss, damage or expense connected with the handling,storage or use of product.